The 1TB SanDisk Ultra 3D SSD (SDSSDH3-1T00) Review

3D NAND, nCache 2.0 Technology, SSD Controller & SATA Interface

The WD 3D NAND Technology

Western Digital first announced their 64-layer 3D NAND technology, also known as BiCS3, last year. However, it was only slated for commercial volume production in the first half of 2017.

BiCS3 was developed jointly with their technology and manufacturing partner, Toshiba. It not only uses 64-layers, but also 3-bits-per-cell technology to achieve high capacity (256 to 512 gigabits per chip) and performance at a much lower cost.

 

SanDisk nCache 2.0 Technology

SanDisk nCache 2.0 is a proprietary pseudo-SLC caching technology that greatly increases the write performance of the solid state drive. Here is an old infographic (from their Ultra II SSD) that shows how it works :

A small portion (about 4%) of the NAND memory blocks are set to run in the SLC mode, which allows for a much higher write speed. This SLC portion serves as a fast write cache for all writes to the drive, allowing for write speeds of up to 530 MB/s.

The data is later transferred to the TLC portion using the special On Chip Copy feature. This proprietary feature allows the transfer to occur internally on-die without affecting any other transfers.

In a 1TB drive, about 40 GB is reserved for use as the nCache 2.0 write cache. That translates into an effective write cache size of about 13 GB.

[adrotate group=”1″]

 

The Marvell 88SS1074 SSD Controller

The 1TB SanDisk Ultra 3D SSD (Price Check) uses the Marvell 88SS1074 SSD controller, which boasts the following key features :

  • Supports up to 4 NAND channels, with up to 8 NAND chips per channel
  • Features Marvell’s third-generation NANDEdge low-density parity check (LDPC) technology
  • Supports SATA 3.2 (6.0 Gbps)
  • Toggle 2 and ONFI2 support at up to 400 MT/s
  • Integrated DEVSLP (Device Sleep) mode for low power support
  • Supports 256-bit AES hardware encryption
  • Built on 28 nm CMOS process

The Marvell NANDEdge LDPC technology allows for reliable on-the-fly error correction of the 3-bit TLC flash memory, with minimal impact on latency, performance and power consumption.

However, the Marvell 88SS1074 is likely to fall short in sustained throughput, because it only supports 4 NAND channels. Competing controllers like the Phison S10, for example, boast 8 NAND channels, allowing twice as many NAND chips to be accessed simultaneously.

 

SATA 6 Gb/s Interface

The 1TB SanDisk Ultra 3D SSD (Price Check) is a Serial ATA drive, with native support for SATA 6 Gb/s interface. It is backward-compatible, so you will have no problem using it with older SATA 3 Gb/s controllers. However, the faster SATA 6 Gb/s interface is necessary for optimal performance because this SSD is capable of a peak transfer rate of 560 MB/s.

Like all Serial ATA drives, it comes with the standard SATA data (left) and power (right) connectors, and is hot-pluggable. That means you can connect and disconnect this solid state drive while the PC is still running. There is no jumper block, because there’s really nothing for you to set. It’s just plug and play!

Next Page > SSD Endurance & Maintenance

 

Support Tech ARP!

If you like our work, you can help support our work by visiting our sponsors, participating in the Tech ARP Forums, or even donating to our fund. Any help you can render is greatly appreciated!


Leave a ReplyCancel reply